The Restoration of Endodontically Treated Teeth Using Indirect Full Coverage Restorations Compared to Direct Composite Resin Restorations

Description

The management of posterior endodontically treated teeth (ETT) is still to this day considered a controversial topic.The use of full cuspal coverage restoration for the management ETT was advocated by many clinical studies and supported by systematic reviews. However, most of the studies did not take into account the amount of tooth structure remaining before providing cuspal coverage. An ETT tooth with an MOD cavity will be at a higher risk of fracture than an ETT tooth with just an occlusal cavity. Managing both with cuspal coverage could be considered an overtreatment and an unnecessary removal of tooth structure. The strength and fracture resistance of the tooth has been shown to be positively correlated with the amount of tooth structure remaining. A more conservative treatment option could be selected for an ETT with good amount of remaining tooth structure such as direct restorations.

The aims of this randomized clinical trial is to compare the survival and success of ETT with occlusal cavities and at least three intact axial walls, when restored through the use of indirect full cuspal coverage restorations vs direct composite resin restorations.

The groups are:

Group 1: Managed with direct intracoronal composite resin restoration. Group 2: Managed with a direct composite resin restoration, followed by an indirect full coverage restoration.

Patients will be recalled at 1 year, 3 years and 5 years.

Treatment protocol for each group Group 1: Patient receiving a composite resin restoration. Following rubber dam isolation, the temporary restoration will be removed. The enamel will be selectively etched with 37% phosphoric acid and rinsed and dried thoroughly till a white frost appearance appeared. An adhesive system (ScotchBond Multi-Purpose - 3M ESPE) will then be applied to the dentine according to the manufacturer instructions and then will be cured for 30 seconds. The direct restoration will be made using a microhybrid resin composite (Filtek Z350, 3M ESPE), which will be applied in increments and each increment cured for 40 seconds. Glycerin will be applied to the final restoration and cured for 5 seconds to prevent the development of the oxygen inhibition layer. The restoration will then be finished with ultra-fine diamond finishing burs, and polished with Sof-Lex discs (3M ESPE) and 0.1 micrometer particle size diamond paste. Occlusion will be checked to conform to the patient's current occlusion status and make sure no interferences were introduced.

Group 2: Patients receiving a composite resin restoration and followed with an indirect full coverage restoration.

The same steps used as for group 1 would be followed to build the composite resin core. This will be followed with a preparation for the indirect full cuspal restoration. Three additional silicone putty indices will be made; one will be made for the production of a provisional crown, and the other two will be cut and used as reduction indices (one will be cut mesio-distally and the other one will be cut facially-lingually/palatally). The preparation will be carried out with diamond burs. The guidelines to be followed will

include

• Supra or equigingival margins if aesthetic was of concern.
• Chamfer finish-line
• 2 mm occlusal reduction;
• 1.5 mm axial reduction all around Following the application of two double retraction cord sizes 00 and 0 (Ultradent), the impression will be made with additional silicone (Zermack) and the cast poured in Die stone. The crown will be fabricated in the laboratory.

The temporary crown made from self-cure bisacrylic (Protemp, 3M ESPE) would be cemented using Eugenol free temporary crown and bridge cement (TempBond). All crowns will be cemented after 1 week using Resin modified glass ionomer cement (RelyX luting plus, 3M ESPE).

Follow-up appointments and data Collection

Clinical evaluation will include:

• Visual inspection conducted with loops at magnification 4.5
• Examination of the continuity of the margins of the restoration with the tooth structure by use of an explorer
• Periodontal probing performed with a periodontal probe.
• Color photos (1:1 mirror shots) of the restorations were taken with standard film
• Periapical and bitewing radiographic examination was performed by use of a paralleling technique at 65 kV and 8 mA.
• Patients reported outcome measures (PROM)

Evaluation of success or failure will be performed by 2 examiners other than the operator.

Details